Research Article
BibTex RIS Cite

Cooling of the Rubber Embossing Cylinder for Tissue Paper

Year 2024, Volume: 10 Issue: 1, 172 - 182, 30.04.2024

Abstract

In this study, the cooling system for the rubber roller in an embossing machine is experimentally examined to reduce the surface temperature increase and extend the working life of the rubber roller. The embossing process generates significant heat, leading to deformation and reduced efficiency of the rubber cylinder over time. In this study, experiments were conducted at a machine speed of 350 m/min, demonstrating that the rubber cylinder begins to deteriorate at a surface temperature of 46 °C under specified pattern density conditions. A cooling system was designed to address this issue, and experiments were conducted with a chiller unit to cool the rubber cylinder from within. The designed system maintained a surface temperature of approximately 5 °C lower than the damage threshold, thus prolonging the operational life of the rubber cylinder. However, operating the rubber cylinder at this temperature is a temporary solution, and further improvements are required for higher machine speeds or increased pattern densities. Future studies could explore the use of chillers with different temperature ranges and flow rates and redesign the experimental setup to enhance heat transfer efficiency. These accomplishments would contribute to the development of an optimized cooling solution for rubber cylinders, ensuring sustained performance under varying operational conditions in embossing machines.

References

  • [1] J. C. Vieira, P. T. Fiadeiro, and A. P. Costa, “Converting Operations Impact on Tissue Paper Product Properties – A Review,” Bioresources, vol. 18, no. 1, 2023. doi:10.15376/BIORES.18.1.VIEIRA
  • [2] Y. Chen et al., “Parameter optimization of rubber cylinder of expansion liner hanger based on numerical simulation,” Journal of Engineering and Applied Science, vol. 69, no. 1, pp. 1–18, Dec. 2022. doi:10.1186/S44147-022-00086-4
  • [3] J. Zhang, M. Sahli, J. C. Gelin, and T. Barrière, “Roll manufacturing of polymer microfluidic devices using a roll embossing process,” Sens Actuators A Phys, vol. 230, pp. 156–169, Jul. 2015. doi:10.1016/J.SNA.2015.03.002
  • [4] M. D. Fagan, “A Novel Process for Continuous Thermal Embossing of Large- Area Nanopatterns onto Polymer Films,” Masters Theses, University of Massachusetts Amherst, Massachusetts, USA, 2008.
  • [5] M. D. Fagan and B. H. Kim, “A Novel Process for Continuous Thermal Embossing of Large-Area Nanopatterns onto Polymer Films,” Advances in Polymer Technology, vol. 28, no. 4, pp. 246–256, 2009. doi:10.1002/adv.20167
  • [6] W. Ma, H. Yu, Y. Liu, and C. Qian, “Numerical simulation and parameter sensitivity analysis for the cooling of rolling rubber-film on cooling-drums,” J Phys Conf Ser, vol. 1549, no. 4, p. 042115, 2020. doi:10.1088/1742-6596/1549/4/042115
  • [7] Y. Deng, P. Yi, L. Peng, X. Lai, and Z. Lin, “Flow behavior of polymers during the roll-to-roll hot embossing process,” Journal of Micromechanics and Microengineering, vol. 25, no. 6, p. 065004, May 2015. doi:10.1088/0960-1317/25/6/065004
  • [8] A. Perez, R. R. Van Der Woude, and R. Dekker, “Rotor Cooling Concept for the ASuMED Superconductive Motor,” IOP Conf Ser Mater Sci Eng, vol. 502, no. 1, p. 012139, Apr. 2019. doi:10.1088/1757-899X/502/1/012139
  • [9] W. Li, S. Song, Y. Zhai, Y. Zhang, P. Yi, and X. Lai, “Rheological behavior of ethylene–vinyl acetate copolymer and fabrication of micropyramid arrays by roll-to-roll hot embossing on its thin films,” J Appl Polym Sci, vol. 134, no. 34, pp. 1–9, 2017. doi:10.1002/app.45228
  • [10] W. Li, Y. Zhai, P. Yi, and Y. Zhang, “Fabrication of micro-pyramid arrays on PETG films by roll-to-roll hot embossing,” Microelectron Eng, vol. 164, pp. 100–107, 2016. doi:10.1016/j.mee.2016.08.001
  • [11] J. C. Vieira et al., “Embossing Lines and Dots Geometry Effect on the Key Tissue Paper Properties with Finite Element Method Analysis,” Polymers 2022, Vol. 14, Page 3448, vol. 14, no. 17, p. 3448, Aug. 2022. doi: 10.3390/POLYM14173448
  • [12] A. M. Morega, I. Dobrin, M. Popescu, and M. Morega, “Heat transfer analysis in the design phase of a high temperature superconductor motor,” in Proceedings of the 12th International Conference on Optimisation of Electrical and Electronic Equipment, OPTIM, pp. 401–406, 2010. doi:10.1109/OPTIM.2010.5510528
  • [13] S. Kim, Y. Son, H. Park, B. Kim, and D. Yun, “Effects of Preheating and Cooling Durations on Roll-to-Roll Hot Embossing,” Microscopy and Microanalysis, vol. 21, no. 1, pp. 164–171, Feb. 2015. doi:10.1017/S1431927614013324 [14] J. Liu, H. Chen, S. Huang, Y. Jiao, and M. Chen, “Recent Progress and Prospects in Liquid Cooling Thermal Management System for Lithium-Ion Batteries,” Batteries 2023, Vol. 9, Page 400, vol. 9, no. 8, p. 400, Aug. 2023. doi:10.3390/BATTERIES9080400
  • [15] J. Zhang, X. Jia, and Q. He, “Mechanical, thermal, and friction properties of addition-type fluororubber co-filled with Al2O3 particles at high temperature,” Polym Test, vol. 96, p. 107131, Apr. 2021. doi:10.1016/J.POLYMERTESTING.2021.107131

Gofraj Sistemindeki Lastik Silindirin Soğutulması

Year 2024, Volume: 10 Issue: 1, 172 - 182, 30.04.2024

Abstract

Bu çalışmada, gofraj makinesindeki kauçuk silindir için soğutma sistemiyle yüzey sıcaklık artışı azaltılarak kauçuk silindirin çalışma ömrünün uzatılması deneysel olarak incelenmiştir. Gofraj işlemi önemli miktarda ısı ürettiğinden dolayı zamanla kauçuk silindirin şekil değiştirmesine ve verimliliğinin azalmasına neden olmaktadır. Bu sorunu ele almak için bir soğutma sistemi tasarlanmış ve kauçuk silindiri içeriden soğutmak için bir chiller ünitesi ile deneyler yapılmıştır. Deneyler belirli bir desen yoğunluğu koşulları altında, 350 m/dak makine hızında gerçekleştirilmiştir. Soğutma işlemi uygulanmadan silindirin yüzey sıcaklığı ölçülmüş ve hasara uğrama süresi tespit edilmiştir. Soğutma işlemi uygulandığındaki yüzey sıcaklığı da ölçülerek farklar belirlenmiştir. Deney şartlarında kauçuk silindirin 46 °C yüzey sıcaklığında bozulmaya başladığı sonucu elde edilmiştir. Tasarlanan soğutma sistemiyle yüzey sıcaklığını hasar eşiğinden yaklaşık 5 °C daha düşük tutarak kauçuk silindirin işletme ömrünü uzatılmıştır.

References

  • [1] J. C. Vieira, P. T. Fiadeiro, and A. P. Costa, “Converting Operations Impact on Tissue Paper Product Properties – A Review,” Bioresources, vol. 18, no. 1, 2023. doi:10.15376/BIORES.18.1.VIEIRA
  • [2] Y. Chen et al., “Parameter optimization of rubber cylinder of expansion liner hanger based on numerical simulation,” Journal of Engineering and Applied Science, vol. 69, no. 1, pp. 1–18, Dec. 2022. doi:10.1186/S44147-022-00086-4
  • [3] J. Zhang, M. Sahli, J. C. Gelin, and T. Barrière, “Roll manufacturing of polymer microfluidic devices using a roll embossing process,” Sens Actuators A Phys, vol. 230, pp. 156–169, Jul. 2015. doi:10.1016/J.SNA.2015.03.002
  • [4] M. D. Fagan, “A Novel Process for Continuous Thermal Embossing of Large- Area Nanopatterns onto Polymer Films,” Masters Theses, University of Massachusetts Amherst, Massachusetts, USA, 2008.
  • [5] M. D. Fagan and B. H. Kim, “A Novel Process for Continuous Thermal Embossing of Large-Area Nanopatterns onto Polymer Films,” Advances in Polymer Technology, vol. 28, no. 4, pp. 246–256, 2009. doi:10.1002/adv.20167
  • [6] W. Ma, H. Yu, Y. Liu, and C. Qian, “Numerical simulation and parameter sensitivity analysis for the cooling of rolling rubber-film on cooling-drums,” J Phys Conf Ser, vol. 1549, no. 4, p. 042115, 2020. doi:10.1088/1742-6596/1549/4/042115
  • [7] Y. Deng, P. Yi, L. Peng, X. Lai, and Z. Lin, “Flow behavior of polymers during the roll-to-roll hot embossing process,” Journal of Micromechanics and Microengineering, vol. 25, no. 6, p. 065004, May 2015. doi:10.1088/0960-1317/25/6/065004
  • [8] A. Perez, R. R. Van Der Woude, and R. Dekker, “Rotor Cooling Concept for the ASuMED Superconductive Motor,” IOP Conf Ser Mater Sci Eng, vol. 502, no. 1, p. 012139, Apr. 2019. doi:10.1088/1757-899X/502/1/012139
  • [9] W. Li, S. Song, Y. Zhai, Y. Zhang, P. Yi, and X. Lai, “Rheological behavior of ethylene–vinyl acetate copolymer and fabrication of micropyramid arrays by roll-to-roll hot embossing on its thin films,” J Appl Polym Sci, vol. 134, no. 34, pp. 1–9, 2017. doi:10.1002/app.45228
  • [10] W. Li, Y. Zhai, P. Yi, and Y. Zhang, “Fabrication of micro-pyramid arrays on PETG films by roll-to-roll hot embossing,” Microelectron Eng, vol. 164, pp. 100–107, 2016. doi:10.1016/j.mee.2016.08.001
  • [11] J. C. Vieira et al., “Embossing Lines and Dots Geometry Effect on the Key Tissue Paper Properties with Finite Element Method Analysis,” Polymers 2022, Vol. 14, Page 3448, vol. 14, no. 17, p. 3448, Aug. 2022. doi: 10.3390/POLYM14173448
  • [12] A. M. Morega, I. Dobrin, M. Popescu, and M. Morega, “Heat transfer analysis in the design phase of a high temperature superconductor motor,” in Proceedings of the 12th International Conference on Optimisation of Electrical and Electronic Equipment, OPTIM, pp. 401–406, 2010. doi:10.1109/OPTIM.2010.5510528
  • [13] S. Kim, Y. Son, H. Park, B. Kim, and D. Yun, “Effects of Preheating and Cooling Durations on Roll-to-Roll Hot Embossing,” Microscopy and Microanalysis, vol. 21, no. 1, pp. 164–171, Feb. 2015. doi:10.1017/S1431927614013324 [14] J. Liu, H. Chen, S. Huang, Y. Jiao, and M. Chen, “Recent Progress and Prospects in Liquid Cooling Thermal Management System for Lithium-Ion Batteries,” Batteries 2023, Vol. 9, Page 400, vol. 9, no. 8, p. 400, Aug. 2023. doi:10.3390/BATTERIES9080400
  • [15] J. Zhang, X. Jia, and Q. He, “Mechanical, thermal, and friction properties of addition-type fluororubber co-filled with Al2O3 particles at high temperature,” Polym Test, vol. 96, p. 107131, Apr. 2021. doi:10.1016/J.POLYMERTESTING.2021.107131
There are 14 citations in total.

Details

Primary Language English
Subjects Energy Generation, Conversion and Storage (Excl. Chemical and Electrical)
Journal Section Research Articles
Authors

Cem Sarı 0000-0001-7277-1021

Bayram Kesmen 0000-0002-1636-9676

Ali Kibar 0000-0002-2310-1088

Early Pub Date April 30, 2024
Publication Date April 30, 2024
Submission Date February 13, 2024
Acceptance Date March 18, 2024
Published in Issue Year 2024 Volume: 10 Issue: 1

Cite

IEEE C. Sarı, B. Kesmen, and A. Kibar, “Cooling of the Rubber Embossing Cylinder for Tissue Paper”, GJES, vol. 10, no. 1, pp. 172–182, 2024.

Gazi Journal of Engineering Sciences (GJES) publishes open access articles under a Creative Commons Attribution 4.0 International License (CC BY). 1366_2000-copia-2.jpg